PV8502 Figma Goblin Slayer (PVC) Out of Stock
Greetings Guys He does not let anyone roll the dice. THis Figma of Goblin Slayer has arrived me safe and sound. Well, he looks as great as he is describeb. The Joints are all in a formidable Shape. None is too lose nor too hard moving. Here and there were some very small seamlines or grates. But nothing, what would disturb me too much. He is very detailed. The Armor has here and there some nicks. The clothes are good shaped. And so are the many belts and pouches. The fur around his neck looks fluffy. And the small hair bundle on his helmet looks good. He comes with 2 weapons. His well known short sword and a club. Both are very good designed, especially the club, cause it really looks crude. The Sword can be sheated in the scabbard on his left. His shield is a little bit biggeras described and in the Manga/Anime. The left hand is hidden behind the shield, but originaly it is clearly visible, and the edge doesn`t goes over his elbow. And so the cross shaped scar/nick is bigger. But this detail is not really that bad. To the colouring. Hmm I´m not really fond of the colouring of the Armor plates. They looks too polished and clear. And what I absolutely dislike is, that they coloured the plates on the Legs in a different tone than the ones on his upper body, and that the visor is also in another, lighter tone. His Armorplates should be in one color, cause they are likely made out of the same material. But the clothes on him are nice coloured. They looks great, but I think the belts could have been shaded. Well that´s it for the Figma of Goblin SLayer. I also got the Nendoroid of him, so please read the feedback to his Nendoroid as well. With best regards Mr.Li
Zan Li (Germany)
PV8055 Himura Kenshin (PVC) Out of Stock
Greetings Guys Himura Kenshin aka Battosai the Manslayer has come in to my house. Glad I´m not his target. First things first. He comes with a large black Base, with some golden cherry blossom petals printed on. There is a big squareshaped Pin in the foothold. But strangely there is no other small Pin there for his left foot. But there is a small hole in his left foot, for a Pin. In the base is something that should be the Pin, but its way off. It`s approximately 8mm off position. After some research, I learned, that other people have the same Problem. They even posted a official statement from GSC, that says, that all the Bases have the same structure and so it`s not a defect. Seriously GSC and Max Factory?!? That´s very unsatisfying for me. Well let´s go on! After fixing Kenshin on the Base, I could inspect him further. And WOW! Just looking at him, you can feel his powerful movements. His clothes enhance this effect. They are fluttering, but in a very realistic way. Alle the folds on his clothes also looks realistic. Even his Hair is fluttering wildly, cause of his explosive movement from his Attack. The Scabbard of his Katana can be easily shoved into his left hand, where it perfectly fits into his hand. The Scabbard is not hollow, but it`s front has a strange shaped hole. The Sabakato, Kenshins famed Weapon. Well it can also easily shoved into his right hand. But his hand is to wide, so you have to be careful, cause the Katana fell out of his hand. And also, when I took a closer look at this Sabakato, I saw that it`s double egded! The Backside of this Sabakato is also edged. Well there is nothing to complain about the colouring. The folds are realisticaly shaded, while the sublime places are highlighted. And all in smooth Transitions. His face is also very good. This sharp look at the enemy he`s striking at. And also his trademark, the cross shaped Scar. I´m out of space again I´m not 100% satisfied but I won`t regret buying him. Best Regards Mr.Li
Zan Li (Germany)
FG10949 Kurone Pre Order
I'm glad this kit was actually made quite quickly compared to other kits I still have in pre-order. My copy of this kit has some really bad issues though with the fitting of the interchangeable chest, the frilly back skirt, and the other hip section of the second hip part. The parts didn't fit well at all. For the hip part I had to remove a good chunk of the support that goes down in order to for that part to finally fit well. For the skirt, I'm going to have to drastically heat bend the middle of the skirt to fit on both hips and then fill in the connections for anything above it. I'm still not sure what I'm going to do with the two different chest choices in order to make them fit properly, I might just stick with one of them to make it easier for me if I have to completely remove the connections for that section, not to mention the odd mold line in different areas on both chests - looks almost like hair line fractures. Other than that the detail in the rest of the parts looks great but the issues are really going to take me a while to fix before I can even paint it.
FG5116 Velvet In Stock
This kit had some issues with the small parts that connect the chains with the gems and also with the red pieces that complete the red parts on the shoulders. Its going to take a bit of time to fix up the small issues. I would have loved to have some small yellow star decals for the hat.
FG11058 Kusunoki Nozomi In Stock
There's a small issue with spacing between the breast and the abdomen, I'll fix that while I modify the hair. Not a big fan of the two ponytail hair style so I might just fill in the holes to make it into short hair.
FG6187 Ms.Marvel Pre Order
It would have need nice to have at least a picture of how the effect parts for the hands were supposed to go together, it took me a bit to figure it out. Other than a shoulder piece not wanting to fit properly everything was pretty good.
FG9522 Valkyrie Pre Order
Overall impressions are good. The fit of the parts was almost flawless. There was one major issue with the figure's right arm. The peg that the other pieces fit into on the right harm connection (from the torso) was missing. I checked the product photos and the instruction guide and they show a peg there, but the kit I had only had a little nub (less than half the length it should to be) where that peg is supposed to be. Perhaps a quality control issue, but this was easily alleviated with pinning and a liberal application of putty. It will still require some fitting and adjustment, but it's nothing that can't be corrected. The QC numbers on the card with the kit are 376, 399 (first QC), and 386 (second QC). How this got past three QC members without noticing the arm peg being more than half gone is beyond my understanding, but, again, it's nothing that can't be corrected.
Diceman20 (United States)
RT2274 NZ-666 Kshatriya Pre Order (Purchased)
awesome and big! the kit is very complex and it will be hard work to assemble it and paint it. Once finished it will be a magnificent piece having already painted one I can advise to mount it first without glue to try the laying and add metal pins
Johnny Reb. ( Italy ) (Italy)
Copyright © 2001-2019 e2046.com - All rights reserved. © 2019 e2046.com